GALVANIZED STEEL WIRE FOR CONDUCTORS AND CABLES
  • Standard: ТU 14–4–1457-87
  • Diameter: from 0,30 mm up to 0,50 mm
  • Application: for production of conductors and cables
Instructions
Recommendations
Packaging
Calculator
Contacts

ТU 14–4–1457–87

ТU 14–4–1457–87

Acc to mechanical properties the wire is produced:

  • Classes 1, 2;

Acc to the type of coating:

  • galvanized – group «G».
MECHANICAL PROPERTIES OF WIRE
Wire diameter, mmTensile strength, N/mm2Number of twists, not lessTensile strength, N/mm2Number of twists, not lessZinc surface density, g / m2,

not less

1 class2 classgroup «G»
0,31960-2340501570-19505530
0,41860-2240451470-18505040
0,51760-2070351370-17504050
A wire break with a knot should be at least 52% of a wire break without a knot.

RECOMMENDATIONS

Before use the wire must be stored in dry, ventilated rooms with low humidity and without sudden changes in temperature to prevent rusting due to moisture condensation.

Before unwinding the wire in the coils, you must first release the coil from the bindings. This must be done carefully, especially when removing the end of the knitting wire threaded through a coil to prevent pulling out and entangling the turns of wire.

Then release the upper end of the wire threaded through the upper turns around the entire circumference of the coil. Before installing and threading the wire into the machine, make sure that the wire is not interwoven with adjacent turns. To do this, it is necessary to lift the end and several turns of wire and then put one turn back into the coil, making sure that there is no “overlapping” of the turns. This will prevent entanglement and wire breakage during the unwinding process.

Before unwinding coils of Z-2 or coils of another type, it is necessary to assemble the coils into a special detachable reel or other unwinding device, tightly fix the cheeks of the coil, ensuring maximum pressure against the wire to prevent “tightening” of the wire between the coils and the cheek of the unwinding device, which can lead to a break wire during unwinding and only after that release the coil from packing metal tapes. After that, tighten the coil or other device again for maximum clamping of the wire coil. Find and free the end of the wire, making sure that there is no “overlap” of the wire through adjacent turns. This will eliminate wire breaks during unwinding.

Spools BS-60

Each spool is wrapped with waxed paper, which is attached with twine; packed spools are stacked on a wooden pallet measuring (1070 x 815) mm. When packing the spools, the pallet is pre-lined with plastic wrap, a sheet of cardboard and a cardboard layer is laid between each row of spools. The spools laid out on a pallet are tied with a metal tape (0.5x16) mm, covered with a plastic film on top and wrapped with “stretch” film.

  • Type of winding:Spools BS-60
  • Dimensions, mm, d*D*h:118х255х152
  • Weight kg:16 – 30
  • Diameter range, mm:0,3 – 0,5
  • Type of winding:Spools BP-60S
  • Dimensions, mm, d*D*h:118х255х152
  • Weight kg:16 – 25
  • Diameter range, mm:0,3 – 0,5
Coils

The coils are tied with the same wire or heat-treated wire with a diameter of 0.8 mm and stacked in wooden boxes with a size of (1100 * 880 * 715) mm for a package of 1000 kg and a size of (1100 * 880 * 550) mm for a package of 500 kg. Boxes are pre-lined with plastic wrap. At the request of the consumer, each coil of wire must be packed in waxed paper and each row of bundles is laid with corrugated cardboard.

  • Type of winding:Coils
  • Dimensions, mm, d*D*h:140х240х70
  • Weight kg:7 – 14
  • Diameter range, mm:0,3 – 0,5

Calculator

Choose parameters for calculation: