CARBON WIRE FOR MESH
  • Standard: TU 14 – 4- 1566 – 89
  • Diameter: from 1,30 mm up to 5,00 mm
  • Application: for corrugated mesh production
Instructions
Recommendations
Packaging
Calculator
Contacts

TU 14 – 4 – 1566 – 89

TU 14 – 4 – 1566 – 89

According to mechanical properties:

  • First class – 1;
  • Second class – 2.

Type of coating:

  • without coating
MECHANICAL PROPERTIES
Wire diameter, mmDiameter tolerance, mmTensile strength, N/mm2 (kgs/mm2)Kink numberTwisting number
high accuracyNot less
1 class2 class1 class2 class
1,3± 0,031370 – 1700 (140 – 173)12102617
1,412102617
1,61270 – 1570 (130 – 160)17152617
1,814132617
2,012112616
2,219172415
2,519172415
3,011102013
3,6± 0,041180 – 1470 (120 – 150)1191913
4,0871513
5,01080 – 1370 (110 – 140)119129

RECOMMENDATIONS

Before use the wire must be stored in dry, ventilated rooms with low humidity and without sudden changes in temperature to prevent rusting due to moisture condensation.

Before unwinding the wire in the coils, you must first release the coil from the bindings. This must be done carefully, especially when removing the end of the knitting wire threaded through a coil to prevent pulling out and entangling the turns of wire.

Then release the upper end of the wire threaded through the upper turns around the entire circumference of the coil. Before installing and threading the wire into the machine, make sure that the wire is not interwoven with adjacent turns. To do this, it is necessary to lift the end and several turns of wire and then put one turn back into the coil, making sure that there is no “overlapping” of the turns. This will prevent entanglement and wire breakage during the unwinding process.

Before unwinding coils of Z-2 or coils of another type, it is necessary to assemble the coils into a special detachable reel or other unwinding device, tightly fix the cheeks of the coil, ensuring maximum pressure against the wire to prevent “tightening” of the wire between the coils and the cheek of the unwinding device, which can lead to a break wire during unwinding and only after that release the coil from packing metal tapes. After that, tighten the coil or other device again for maximum clamping of the wire coil. Find and free the end of the wire, making sure that there is no “overlap” of the wire through adjacent turns. This will eliminate wire breaks during unwinding.

Skein

Each skein is tied with a heat-treated wire of Ø1.8 mm in at least four places evenly spaced around the skein, lubricated with industrial oil and packaged in a polypropylene fabric. By agreement with the consumer, it is not greased or packaged. It is packaged (in 4 - 5 skeins) with a metal steel tape (0.5x16) mm in four places evenly spaced around the package circumference. The tapes are fixed with heat-treated wire Ø1.8 mm around the circumference of the middle of the package.

  • Type of winding:Skein
  • Dimensions, mm, d*D*h:400х650х200
  • Weight kg:120 - 150
  • Diameter range, mm:1,3 – 2,5
Coil

Each skein is tied with a steel metal tape (0.6x19) mm in at least six places evenly spaced around the skein. The tapes are fixed with heat-treated wire Ø 1.8 mm around the skein. The wire is lubricated with industrial oil, packaged in polypropylene and the cloth is tied around the circumference with tape. In agreement with the consumer production without lubrication and without packaging is allowed.

  • Type of winding:Coil
  • Dimensions, mm, d*D*h:400х800х600
  • Weight kg:500 - 900
  • Diameter range, mm:3,0 – 5,0

Calculator

Choose parameters for calculation: